689393

NBA No Tools Basketball System 44"

44" fan backboard, height adjustment from 7.5" to 10" in 6" increments. Portable t-base can be filled with water or sand for stability.

689395

NBA Platinum Portable Basketball System

Spaldings newly developed Screw Jack Elevator System allows you to adjust the basket to the exact height you desire. Board Composition: Acrylic Board Size: 52 - 132cm Lift Type: Screw Jack Elevator System Base Mobile, fills with sand or water, 154 litre capacity Rim HEAVY DUTY Pro Slam Height Adjustable: 7.5 - 10/2.3m - 3.05m Assembly Time Approx. 4-5 hours.

A16-600

B/Ball B/Board - International Mobile
3250mm Overhang

International standard. Incorporates mini basketball height. Low profile base for minimum obstruction for spectators behind backboard. Backboard frame, underside of arms and the complete base are padded. As the backboard is raised, cams lower a wide front rubber covered foot to the floor. This takes the load of the backboard off the wheels to reduce movement during use. Rear anchor points and floor fixings are included. Backboard: glass, armour plated A16-45. Ring: snap down A16-43. Operation: Push button, electric 240volt hydraulic pump. Weight: 1200kg 1200kg.hydraulic pump. Weight: 1200kg.hydraulic pump. Weight:

BB1000

Backward Hinged Basketball System

40mm SHS backboard frame with BB900 backboard, ring and net. This model is supported by diagonally braced arms made from 75 x 50mm RHS. Fixing points for both pivot arms, the winch pulley block and support cables must be installed during building construction. Special members can be made to suit, at additional cost, if required. Winch not included. Winch may be ordered separately depending on the type required. Price on application.

BB1050

Side Swing Basketball Tower 3 Post
System

Same features as BB1040 but this structure may be locked to a third pole. Ideal in high-wind areas or for security purposes.

BB1070

Side Swing Basketball Tower 3 Post Syste
W50 rating

Same features as BB1050 but the third pole is made from heavy-duty 165mm hot-dipped galvanised pipe and uprights are made from heavy-duty 5.4mm wall 140mm diameter hot-dipped galvanised pipe. Designed for wind rating W50.

BB600

Heavy Duty Full Size Basketball Tower

Engineer-designed, heavy-duty 115mm OD round hot-dipped galvanised (before fabrication) strutted tower with hot-dipped galvanised star brace backboard support. Ring is bolted through the steel star brace and cannot be pulled through the backboard. Clearance of 1800mm from the face of the post to the backboard. Supplied with a heavy-duty, powder-coated 20mm double-strutted basketball ring with nethooks (BB821), and an all weather plastic-coated formply backboard, 1800x1050x17mm. All fixings included. Designed for permanent installation. FOR WIND RATING W28 (N1) only.

BB610

Round H/Duty Competition Tower

Engineer-designed, heavy-duty 114mm OD, hot-dipped galvanised (before fabrication) round 90 degree arched tower. Steel reinforced fibreglass fan shaped backboard, 1400x1050mm. Ring is bolted through the steel backboard brace and cannot be pulled through the backboard. 1800mm clearance from face of post to backboard. Heavy duty powder-coated 20mm triple-strutted ring with net hooks (BB826), net, and tamperproof bolts included. Ideal for councils, schools or clubs. Designed for permanent installation, but can be made reversible (see BB610R). For W33 & W41 wind rated areas.

BB610RW50

H/D Reversible Basketball Tower - W50

Same as BB610 but reversible and made from thicker steel to suit higher wind rated areas. For W50 wind rated areas.

BB735R-1200

Reversible Basketball/Netball Tower

Reversible Basketball/Netball Tower 115mm OD high tensile 350 grade tower, with star brace backboard support, backboard and ring as BB600. Tower has a 1200mm clearance from the face of the post to the backboard. Ideal for basketball/netball combination courts where playing to both standard regulation distances. Engineer-designed and approved to suit school, club and council requirements. Can also be made to suit W50 rating.

BB735RW50-1200

Reversible Basketball/Netball Tower W50

Design as per BB735R but contructed to suit W50 wind rating. 1200mm clearance from the face of the upright to the face of the backboard.

BB738R

Super H/Duty Rev BBall Netball Tower

W41 rated wind loading. 140mm OD round hot-dipped galvanised tower. Other features similar to BB735R tower but netball ring is positioned in line with the top of the tower upright for competition play. Ideal for high abuse areas. 2400mm clearance from front of post to face of backboard.

BB750

Adjustable Basketball Tower

75mm SHS powder-coated main uprights with an adjustable slide system behind the backboard. Three heights settings make this system ideal for both junior and senior play. Height is adjusted by releasing a pin on the slide system and relocating it in another position. Very compact in the fold down position. Supplied with a super heavy-duty fully reinforced rectangular or fan-shaped fibreglass backboard, 12 hook 16mm double-strutted ring, net and all fixings. Construction sleeve can be supplied at extra cost if required, CFSS80 1m Reach

Y7-34

Mini B/Ball Height Adjusting Brace
For Y7-31, 36 & 39

Added to Y7-31, 36 or 39 to adjust board from competition height to mini basketball height. Spring loaded pin locates each height and gas strut counterbalances the weight of the board.

Y7-37

B/Ball B/Board 1 Upright No Cantilever
Including Socket

Backboard and frame is fixed directly to a square steel section upright. Options (ordered separately): mini basketball height adjustment A16-650. Netball ring A16-230.

Y7-41

Uprights For Y7-30 4200mm Max Cantilever

Galvanised pipe, end capped. The local conditions and the required basketball backboard arm length determine size of uprights.